How To Explain Door Lock Change To Your Grandparents
How to Do a Door Lock Change
The change of your door lock is a simple and inexpensive way to increase the security of your home. This process isn't for everyone. It requires a certain amount of patience and skill.
You need to replace the cylinder, which is within the knob's body. The cylinder is responsible for recognizing the key as it is put into the lock.
Remove the old lock
The first step to replace the door lock is to take out the old one. It's a fairly simple procedure, but there are some things to be aware of. Make sure your new lock fits your door. This will ensure that it fits snugly and doesn't create a gap around the deadbolt plug or latch.
After you've removed the latch plate look for two bolts or screws on the inside of the casing, which secure the casing and halves of the lock. Take these screws off using a screwdriver and then pull the lock off the door. If you have a mortise lock there could be a set screw at the base of the handle, which binds it to the spindle. Make use of a screwdriver for removing the screw, and then take out the doorknobs.
Take the deadbolt and latch plug from the door jamb. Then, you are able to install your new lock. If you are replacing a mortise you should measure the distance between the lock case and the door edge to make sure that the new lock will fit.
Several reasons might prompt you to change your door lock, including suspecting that someone else has the key or if you're welcoming an incoming roommate. In any event, you could save money by removing the lock yourself instead of paying an expert to do it. It is much easier than most people imagine and can be done in just a few moments.
Begin by removing the handle and trim from the door. With a flat screwdriver remove the trim. You will be able to pull off most of it, and in certain cases the handles may fall off completely. Next, examine the handle for a tiny pinhole on the inside and insert a straightened clip into it. This will trigger the release mechanism, which allows you to take off the handle. Look for a small tab in the interior of the lock and push it with a screwdriver that is flat. After the spindle is removed, you can remove the cylinder and the housing.
The process of selecting a new lock
You have many options when it comes to selecting a new lock. Consider the different types of locks and pick one that is in keeping with the design of your door. Think about the backset, which is the distance between the edge and the center of the hole in the lock. Also, consider the cross bore, a small hole in the middle of your door frame. Select a lock that is suitable for the door's thickness and the swing.
The majority of door locks have been graded by BHMA and the American National Standards Institute to give you an idea of how they will withstand use and how difficult they are to pick or disable. A lock of grade 3 could be the ideal choice for a tranquil apartment complex in the country, while locks that are grade 1 could be more appropriate for an area with a lot of traffic, such as a storefront.
Most smart door locks need a digital code to open. If you're worried about hacking, or other security concerns, speak to an expert locksmith.
Replace the cylinder
It is easy to replace damaged or broken door lock cylinder using a simple DIY project. The trick is to select the right cylinder, and follow the directions that accompany it. The first step is to remove the knob or handle, should there be one, then unscrew the trim that is attached to the base of the lock cylinder by using the help of a screwdriver. Once the trim is removed, you can reach the screws that hold the cylinder in place and remove them with the flat-head screwdriver. The cylinder is then gently pulled away from the door.
Be sure to take measurements of the length of the new cylinder prior to installing it. Find the distance from the center to the left and right sides of the cylinder using the aid of a tape measure. Then, purchase an additional cylinder using the same measurements. This will stop the cylinder from snapping, which can happen when the door is kicked out or when the key gets stuck inside.
Insert the replacement cylinder in the door, and then turn the key. This will ensure that the cylinder is aligned with the carrier, which is normally located on the outside of the lock. You can then loosen the set screws which should be only a couple of turns into the head. You will also need to loosen the screw on the edge of the door that holds the case in place, should there be one.
You can replace the cylinder that was used to lock your old lock with a new one by sliding it into the case, and then tightening the set screws. It is also recommended to reinstall the part that connects the cylinder with the stem for the lock indicator, which you can do by removing three tabs on the back of the cylinder with needle-nose pliers. Attach the bracket that is smaller to the back of the cylinder. Then, you should reinstall the strike plate and latch plate, along with the retaining rings that are attached to the top of the lock cylinder.
Installing the new lock
Start by measuring the door's width if you are replacing a lock that is already in use. Most residential locksets are designed to fit a door thickness of 1 3/8 - 3/4 inch. If your door is thicker it will require a door kit that is thick and includes longer screws and longer tail pieces (for door knobs) or spindle extension (for deadbolts).
The majority of locks come with a detailed instruction manual to help you install the new hardware. Before you begin, read the instructions to make sure you've followed the steps. The guide will give you an idea of the amount of skill that is required to complete the task. If you're changing locks for the first time, you may want to ask an experienced friend for assistance.
double glazing window lock repairs 's a great idea to cover the holes in the old hardware prior to installing the new lock. This will keep the screws from slipping out of the holes and will protect any tile you might have installed in the area. It will also protect your tiles from any damage caused by rust, dirt and grime. SECURAM Touch comes with a strip painter's tape that is intended to be used to protect your painter's tape, but you can also use gaffer's tape or masking tape when you have it.
Once you've removed the screws that hold the interior portion of the lock section to the exterior side, pull it straight away. It is important to do this quickly to prevent the lock from accidentally closing and damaging the mechanism.
If the new lock comes with a latch bolt, fit the new bolt into the upper cross bore. Be sure to put it in the correct place that is usually indicated by an indication on the faceplate. Then, place the latch plate on top of the bolt and screw it into place.
Screw the deadbolt into the jamb of the door. Test the deadbolt by throwing it a few times to verify that it is extended all the way through the strike plate and is secure. If you're using an electronic smart lock, make sure to follow the instructions to program it. This involves downloading an app and registering your e-mail address, confirming your identity and connecting to the wireless network to add your device.